Services

Troubleshooting

25 print defects, their causes and their solutions

25 thermal transfer printing problems analysed by our technicians, with their causes and solutions.

  • Grouped by symptom family: ribbon and core, printer, print quality, unprinted lines and areas, ink, wear and mechanics
  • Analysis and solution written by our technicians, printer by printer where needed
  • Problem not solved? Send us a printed label: our technicians will diagnose the issue
Technician checking a label coming out of a thermal transfer printer
1

Ribbon and core

The ribbon does not fit, is not driven or moves on its core: most often a matter of dimensions, notches or winding.

01

Ribbon too large (diameter) for the printer

Solution

Unwind the roll or remove the outer layers after carefully cutting with a knife. A very thick roll that causes no problem at the start of printing can cause difficulties during printing: the printer may not accept two medium-diameter rolls (unwind and rewind spindles). The printer's job becomes increasingly difficult as the diameter of the rewind-spindle roll grows. When ribbon feed is no longer ensured at the end of the roll, it is often enough to replace the rewind-spindle roll with an empty core.

02

Ribbon too wide for the printer

Solution

No solution. If absolutely necessary, try to re-slit the roll (difficult) or saw it.

03

Core without a notch, but the printer needs one to drive the ribbon

Solution

Using a knife, cut a "V" notch on the appropriate side of the core. This is not very elegant, but works as well as the original notch.

04

Telescoping: the ribbon moves on the core when loaded into the printer

Solution

Cause: the winding is not tight enough during ribbon production. Remedy: try to load the roll while pressing sideways on the core.

Cause: the roll was stored for a long time in low relative humidity (winter). In this case the film winding itself is firm enough; only the core slips inside. Solution: see above.

05

Ribbon poorly positioned on the core, overhanging on both sides

Solution

The wound ribbon is poorly positioned on a fixed-length core suited to certain printers, so the transfer film strip overhangs on both sides.

Either the ribbon was poorly wound onto the core during production, or the ribbon shifted on its core during transport.

In both cases, a workaround can be to carefully move the ribbon along the core to its correct position.

2

Printer

Error messages, printer refusing to start or to stop: printer settings and its ribbon sensor are involved.

06

A TEC printer displays "No Ribbon" although a ribbon is loaded

Analysis

TEC printers distinguish between opaque ribbons and more or less transparent ribbons (grey, colours, etc.). This parameter must be communicated to the machine directly or via an external keypad in the "Parameters" menu. The photoelectric cell "accepts" the ribbon and, to stop printing at the end of the ribbon, waits for an end strip of transparency opposite to the film's programmed parameter — for example a metallised strip that is completely opaque at the end of a grey transfer ribbon considered "transparent".

If the printer is incorrectly programmed, or if the ribbon has a transparency close to the opaque/transparent threshold, the printer issues the "No Ribbon" error.

Solution

Reverse the printer's transparent/opaque parameter. If this does not solve the problem, or if there is no external keypad, stick a piece of ribbon over the photoelectric cell and choose the "opaque" option.

07

The printer will not go "online"

Analysis

Some printers do not accept very light or coloured ribbons because the photoelectric cell that checks for the transfer film does not recognise the ribbon due to its transparency.

Solution

The professional solution is to adjust the position of the potentiometer on the main board so the cell also accepts less opaque ribbons. This is a job for an approved technician.

As a workaround, the user can stick a piece of film or paper over the cell to simulate a more opaque ribbon.

08

No printing

Analysis

The label surface repels ink from the transfer film.

It may be an untreated low-surface-energy synthetic film (such as PE or PP), a film of the same type where the corona treatment has lost its effect due to overly long storage, a surface pre-printed with printing inks, or one with UV-cured varnishes — unsuitable for thermal transfer overprinting.

Solution

Try another ribbon grade. Some UV-curing varnishes make any overprinting impossible; in that case there is no solution.

To find a solution for printing on a difficult surface, you can always try several thermal transfer ribbon grades. Even in very difficult cases, an acceptable result can sometimes be achieved.

09

The printer does not stop at the end of the ribbon

Analysis

The ribbon end, or the ribbon's end strip, is not suited to the printer model.

Solution

Depending on the model, the end strip must be transparent or metallised, or no end strip is needed at all. In the latter case, the printer monitors the rotation of the unwind spindle, so stopping is independent of the ribbon's transparency. In that case, the presence of an end strip may leave a few centimetres — and thus a few labels — unprinted at the end of the ribbon before the printer stops.

3

Print quality

Pale, blurred, uneven or overloaded print: head energy, speed, pressure and ribbon / material match.

10

Irregular dropouts in the print, in the machine direction

Analysis

Residues on the printhead — whitish from the ribbon's back-coating or black from the ribbon's ink layer.

Solution

Remove the residues with a soft cloth and isopropanol.

11

Greyish, non-covering, poor print

Analysis

The printer's temperature setting is too low, or the ribbon and the label material are incompatible.

Solution

Increase the temperature, change the label material or use another ribbon.

12

Text and images are filled in, the ribbon melts

Analysis

Temperature setting too high.

Solution

Reduce the temperature.

13

Blurred print

Analysis

Print speed too high. Print speed is always a compromise between time and print quality. It is often software-controlled. High speed: short print time, lower quality; low speed: longer print time, higher print quality.

Solution

Reduce the print speed.

14

Isolated defects in characters, scattered print defects

Analysis

The label surface and the ribbon are not compatible.

Solution

First try increasing the temperature; if necessary, change the label/ribbon combination.

15

Uneven print across the width

Analysis

The row of dots is not parallel to the transport roller.

Solution

Correct the alignment of the transport roller.

4

Lines and unprinted areas

Longitudinal, transverse or diagonal white lines, spots and unprinted bands: print head, ribbon wrinkles or alignment.

16

White longitudinal lines

Analysis

Faulty dots.

Solution

Replace the printhead. Replacement is needed when this defect makes the printed information unreadable (barcodes). If, however, you print large characters where appearance is not critical, a faulty head may still be usable for a while.

17

White spots or unprinted areas

Analysis

Ribbon coating defect, in the form of lines or spots.

Solution

Replace the ribbon with a defect-free one. Small pinhead-sized defects generally do not affect printing.

18

White lines, often diagonal

Analysis

The ribbon used is much too wide or too narrow relative to the label width.

Solution

The ribbon and labels should be almost the same width. Ideally the ribbon is a few millimetres wider than the labels.

19

White transverse lines, crescent-shaped

Analysis

These "crescents" appear in large-area elements: graphic elements, large barcodes, bold characters. Their cause is a weakening of the base film due to too high a temperature in the printed element compared with its surroundings.

Solution

Reduce the print temperature.

20

Unprinted strip on the inner side of the label

Analysis

The ribbon "telescopes" as it unwinds due to insufficient tension.

Solution

Cut a cardboard washer and place it on the unwind spindle against the edge of the ribbon.

5

Ink, wear and mechanics

Ink coming off, ribbon breaking, noises or fast head wear: mechanical stress and material compatibility.

21

Ink flaking off

Analysis

Flaking occurs only when handling and loading the ribbon into the printer. The ink of some ribbon grades tends to flake more easily; ink adhesion to the base film is inherently poor. Normally the ribbon should work without problem once loaded.

If this is not the case and pieces of ink flake off during printing, the ribbon is probably defective (insufficient ink drying, solvent residue in the ink, ink too thick, etc.).

Solution

In that case: change the ribbon and inform the supplier.

22

Uneven vertical spacing of the printed elements

Analysis

The printhead is clean.

The ribbon's back-coating is probably not homogeneous, is too thin or is absent. This layer is essential for thermal transfer printing — it protects the base film from heat and prevents it melting, helps the film glide over the printhead and reduces electrostatic charge. Its absence leads to the problems described above.

Solution

Replace the ribbon with one from another production batch and inform the supplier.

23

The ribbon tears

Analysis

The ribbon's back-coating is insufficient or absent.

Solution

Use a new ribbon from another production batch.

24

Operating noise

Analysis

Separating the ink layer from its carrier often produces a squeaking noise.

Solution

Some printers (ZEBRA) allow the position of a deflector in front of the head to be adjusted. This can reduce the noise produced.

25

Printhead wears out too quickly

Analysis

The operating temperature is unnecessarily high. The head pressure is too high. The printer and head are not cleaned often enough — cleaning should be done at every ribbon change. A difference between ribbon and label width. Regular use of labels with surface irregularities — for example labels with overprinted holograms, RFID chips or very thick material — causes head wear always in the same place.

Solution

Replace the head and monitor operating conditions carefully to maximise the new head's life. Always: print at the lowest possible temperature, print with the lowest head pressure, avoid overly thick substrates, and use a good-quality transfer ribbon.

Your case is not in the list?

Problem not solved? Our technical team will look into your case and advise you.